JOY Inflatable best deal on inflatable water slide manufacturers for children

 Blue Color Inflatable Water City Slip Slide is with the dimension 20 meter  long and 2.4 meter width single lane (of course it can be double or customized ) is made by 0.55mm PVC tarpaulin which is strong tension . Because the inflatable water slip slide is with sewing workmanship so it need 1 air blower to inflate all the time during the work   .       

Depend upon this style inflatable city water slide , it must be built up on a slipe with 15-30 angles street or hill , so that people can freely slide to the end with water and reach the swimming poool .Climb up ,tumble down ,shake yourself off and try again , once your are successful and reach the top of the slip slide you are ready to slide down . Of course you can add some soap bubble on the slide to make it more smooth and Slippery or all kinds of swim ring to push you fast to slide.In addition , when people are playing , you need to spray water on the surface of the slide. All of our inflatable slides are suitable for a variety of ages , not mattter children or adult .        

All kinds outside activities.  

it must be built up on a slipe with 15-30 angles ,both street and hill 

The slip n slide is a classic backyard activity. That’s why we offer commercial slip n slides for summer camps, resorts and homes that take this time-honored concept and we put our own adventurous twist on it. 

                           

Fastly slide 

With an ultra-slippery tarpaulin surface, all you have to do is add water and soap studs  get ready to slide down the slide.

                           

Anchor around the arch 

OWe will sew a lot of tthe anchors around the each arches of the slip slide for the customer to attach the water pipe or spray . 

                           

blower pipe 

We will make the blower pipe in about 20cm in diameter according to our blower . In order for your convenience to connect the power we will make the one blower pipe each 2 meter  .You can put the extra  blower pipe in the hole .

Sewing machine technology: double stitching everywhere and strong reinforcement at joint part .

Features : work with the blower all the time

With inflatable bottom

VS

single layer bottom

                                      with drain hole easy drain                          you  can open it you can drain the water out of the slide 

VS

Without the drain hole 

1.To find  space , long , wide and high enough to place the tent on the ground .
2.Clean up the site, not allow have sharp objects and high-voltage wires to keep safety .
3.It would be much better if put a cushion under it such as carpets, plastic color cloth protect the tent from sundries .
4.Spread out and flatten the slide on the ground .
5.Connect the air inlet of inflatable slide and the outlet of blower tightly, and then tight alternative air inlet with a rope.
6.When the blower switched on, inflatable slide will be inflated within 2-5 minutes (depend the size of the slide ).
7.If there is a wind, fill the sandbag and tie it to D-rings on the bottom of the tent or tie the Stakes to D-rings on the bottom and insert the stakes in the soil .

If you find a leak, you can wipe the air column first, then apply the surface with soapy water to check the leak. Leakage point If it is a small hole, you can use a small piece of circular maintenance cloth (any specifications of the inflatable tents inside the standard), and then brush dispensing, to be dry after the paste on the leak.
If the leak at the gas column heat seal at the opening of plastic, can be divided into the following steps:
1. First clean up the bonding surface.
2. Guangzhou Joy Inflatable Limited of the inflatable tents will be issued to the bottle of glue, inflatable tent column dedicated plastic, it will be painted on the pre-adhesive surface, must be painted evenly, the thickness of the appropriate brush map twice, you can Sticked up.
3. The shape of the mouth to be designed into a circular or oval, try to avoid the square and acute angle interface shape, lap width can not be less than 30mm.
4. To be glue after evaporation, can be bonded, patch to be flat, no wrinkles, rolling, scraping, while the supply of heat with the hair dryer, easy to bond. Adhesive after 6 hours can be inflated.

1、free design 
2、free repair kit and After sale-service