|Materials||Durable 0.4 mm white color pvc /18.5OZ PVC coated vinyl which is waterproof ,fireproof and u/v protected|
|Inflate and Deflate||Easy to install and take down|
|Sewing machine technology: double stitching everywhere and strong reinforcement at joint part .|
|Features : work with the blower all the time|
|Printing||Logo printed by Digitally printing or Silk-screen printing|
|Air Pump(airtight product)||Air pump with CE/UL certificates, 110V/220V, various powers|
|Accessories||Blower or air pump , repair Kit ,Glue ,Carry bag （for free )|
|Inflatable product is packed by heavy-duty PVC carry bag;|
|air blower/ air pump is packed by exported standard carton.|
Large Outdoor Inflatable Event Tent with Logo Printing
1.USE : Inflatable Marquee tent can be used both indoor and outdoor
different activities, such as wedding party, exhibition, promotion,
sport hall and ect
2.Installation :inflatable tents are easy to set up in a short time, and moveable to another place from one place as requested, it can stand up after inflated by air blower
3.Fix :We have make anchor in the bottom and D ring on the roof for light hanging inside. The tent can resist 6 level wind after fasten the tent.
All kinds outside activities
1.For party event 2. wedding 3. As a store 4.exhibition
Our inflatable tent is with the slant roof .It is easy to drain away the water in the rain or snow day .
Each connect part weld transparent pvc to make sure 100% waterproof for out tent .
All sewing inflatable products are made by high precision machines and using unique 12 in one waterproof nylon threads . We use double stitching for both inside and outside of the products and quadruple stitching for the force loading bottom . For each corner and connection, there are reinforce straps to make sure the product are safe enough for all wind and tension . The length of each single sewing needle is 3mm-8mm
Installation of the tent
1.Site selection: large and high enough to place the tent on the ground .
2. Clean up the site, make sure no sharp objects .And keep away from high-voltage wires.
3. It’s advised to place a sheet of fabric beneath the tent.
5. Connect the air inlet of inflatable tent and the outlet of blower tightly, then tight connect part with a rope.
6. Turn on the blower switch, tent will be inflated within 10-30 minutes (as per the size of the tent ).
7. If there is wind, fill the sandbag and tie it to D-rings on the bottom of the tent or tie the Stakes to D-rings on the bottom and insert the stakes into ground .
Installation of Air Blower:
1. Specification of electricity ranges among different countries. Check and make sure air blower provided matches local system.
2. Keep little children away from air blower’s air inlet. If needed,a protective net is suggested.
1. Under severe weathers (6 grade or above strong wind,heavy rain, snowy, fogy etc), inflatable tent and blower are prohibited to use at outdoors.
2. When encountering any inflation failure, check if there is any leakage, power failure or bad connection.
3. If air pressure is too strong, cover the air inlet of blower for some time.
4. Continuous air supply is needed. Please keep air blower connected and on during use.
1. Clean and dry the damage part .
2. Find from repair kit the repair fabric and cut a suitable piece ,round shape is advised.
4. Paste repair material on the damage part and press for a while. The tent can be used again a few hours later.
5. If there is large-scale non-normal damage,please ask factory for guidance .
High quality inflatable tents are now available on link below.
If you find a leak, you can wipe the air column first, then apply the surface with soapy water to check the leak. Leakage point If it is a small hole, you can use a small piece of circular maintenance cloth (any specifications of the inflatable tents inside the standard), and then brush dispensing, to be dry after the paste on the leak.
If the leak at the gas column heat seal at the opening of plastic, can be divided into the following steps:
1. First clean up the bonding surface.
2. Guangzhou Joy Inflatable Limited of the inflatable tents will be issued to the bottle of glue, inflatable tent column dedicated plastic, it will be painted on the pre-adhesive surface, must be painted evenly, the thickness of the appropriate brush map twice, you can Sticked up.
3. The shape of the mouth to be designed into a circular or oval, try to avoid the square and acute angle interface shape, lap width can not be less than 30mm.
4. To be glue after evaporation, can be bonded, patch to be flat, no wrinkles, rolling, scraping, while the supply of heat with the hair dryer, easy to bond. Adhesive after 6 hours can be inflated.
2、free repair kit and After-Sale service
Hello, please leave your name and email here before chat online so that we won't miss your message and contact you smoothly.