JOY inflatable blow up marquee wholesale for child

Inflatable tent is a kind of tent, using the principle of structural mechanics design framework, the use of gas pressure characteristics of the balloon expansion to form a certain rigid cylinder, through the organic combination of the tent to hold up the skeleton. With the strength of the skeleton material used, you can set the size of the tents, the use of polymer composite materials, the performance of the advantages and disadvantages of the framework of the shelf life of the frame and the maintenance of the rigid, It determines the support of the framework of the limit. Mainly used for moisture, water, wind, dust, sunscreen, disaster relief, field short-term training, Wedding Party Event ,exhibition . Fabric material: Oxford cloth or  PVC.

All kinds outside activities.  1.For party event.  2. wedding.  3. As a store.  4.exhibition.

                           

FIRST

In the removal is the same, the metal stent removal and packaging required by the number of more time-consuming are relatively long. And inflatable tents in the demolition only need to let its natural deflated, or electric blower suction can be !

                           

NEXT

Therefore, compared to ordinary metal bracket tent, the inflatable tent has its unmatched advantages, its light weight, small size, in the transport with ordinary metal bracket tent does not have the advantage. And its erection and removal are very simple, will not waste more manpower and time, especially for emergency response in the emergency use. In the harsh environment can not be reached when the inflatable tent can also be empty.

                           

LAST

You can install or disassemble in a very short time to save you valuable time; better insulation, inflatable tents with high quality pvc waterproof canvas, tear resistance, better tensile strength, anti-aging Better sex, long service life. In the weight and 8 wind load under the safe use of continuous service life of more than 2 years.

Sewing machine for Cube silver tent and high-frequency heat combined for dome tent with the process of production, gas column with PVC double-sided coated cloth, tarpaulin waterproof, anti-ultraviolet materials, with fast forming, high strength, fire, mildew, anti-ultraviolet, moisture Etc. Tent for the inflatable tent, tent frame for the gas column structure, compared with the general metal bracket tent, with a light, folded after the small size, easy to carry and so on.

slope roof good at draining away the water 

VS

flat roof ponding on the roof 

Doors and Windows have single cloth, can be rolled up

VS

Without the cover of door window

Plenty of D-rings

VS

small of D-rings

1.To find  space , long , wide and high enough to place the tent on the ground .
2.Clean up the site, not allow have sharp objects and high-voltage wires to keep safety .
3.It would be much better if put a cushion under it such as carpets, plastic color cloth protect the tent from sundries .
4.Spread out and flatten the tent on the ground .
5.Connect the air inlet of inflatable tent and the outlet of blower tightly, and then tight alternative air inlet with a rope.
6.When the blower switched on, inflatable tent will be inflated within 10-30 minutes (depend the size of the tent ).
7.If there is a wind, fill the sandbag and tie it to D-rings on the bottom of the tent or tie the Stakes to D-rings on the bottom and insert the stakes in the soil .

If you find a leak, you can wipe the air column first, then apply the surface with soapy water to check the leak. Leakage point If it is a small hole, you can use a small piece of circular maintenance cloth (any specifications of the inflatable tents inside the standard), and then brush dispensing, to be dry after the paste on the leak.
If the leak at the gas column heat seal at the opening of plastic, can be divided into the following steps:
1. First clean up the bonding surface.
2. Guangzhou Joy Inflatable Limited of the inflatable tents will be issued to the bottle of glue, inflatable tent column dedicated plastic, it will be painted on the pre-adhesive surface, must be painted evenly, the thickness of the appropriate brush map twice, you can Sticked up.
3. The shape of the mouth to be designed into a circular or oval, try to avoid the square and acute angle interface shape, lap width can not be less than 30mm.
4. To be glue after evaporation, can be bonded, patch to be flat, no wrinkles, rolling, scraping, while the supply of heat with the hair dryer, easy to bond. Adhesive after 6 hours can be inflated.

1、free design.
2、free repair material and repair video.